A system and method monitor operation of a compressor, determine whether the operation of the compressor is outside of a designated range of values, and, responsive to determining that the operation of the compressor is outside of the designated range of values, one or more of (a) prevent communication of a signal to a system controller that controls operation of the compressor, (b) direct a gas from a reservoir to a pressure sensor used by the system controller to determine a gas pressure generated by the compressor, and/or (c) communicate the signal to the system controller that controls operation of the compressor.

A variety of methods and arrangements for reducing noise, vibration and harshness (NVH) in a skip fire engine control system are described. In one aspect, a firing sequence is used to operate the engine in a skip fire manner. A smoothing torque is determined that is applied to a powertrain by an energy storage/release device. The smoothing torque is arranged to at least partially cancel out variation in torque generated by the skip fire firing sequence. Various methods, powertrain controllers, arrangements and computer software related to the above operations are also described.

A method and system are provided with which it is possible to detect non-firing and untimely firing events in internal combustion and, if necessary, the temperature of the gas in the exhaust gas pipe. This is performed in general by measuring the speed of sound and determining the phase angle between the sender and receiver either arranged on different sides of the exhaust gas pipe or on the same side of the exhaust gas pipe. The receiver, depending on the measurement principle, can include one, two, or in special applications three receivers. Additionally, if necessary, it is possible to suppress the structure-borne sound influence on a speed of sound measurement with low cost and high stability.

In a catalyst warming-up control, a first time injection is performed by an injector in an intake stroke. A second time injection is performed with an amount smaller than the first time injection in an expansion stroke after a compression top dead center. In the catalyst warming-up control, an interval from the start of the ignition period of an spark plug to the completion of the second time injection is controlled by the ECU so that the initial flame generated from an air-fuel mixture containing the fuel spray injected by the first time injection is brought into contact with the fuel spray injected by the second time injection.

A control device is configured to perform, when it is estimated that a combustion fluctuation increases, estimation related to an ignition delay for initial flame generated from a discharge spark and an air-fuel mixture containing fuel spray injected by intake stroke injection. When it is estimated that the ignition delay for the initial flame is increased from that before the increase in the combustion fluctuation, an injection amount in expansion stroke injection is reduced in a next time cycle. When it is estimated that the ignition delay for the initial flame is reduced from that before the increase in the combustion fluctuation, the injection amount in expansion stroke injection is increased in a next time cycle.

An internal combustion engine (1) includes: an exhaust gas recirculation unit equipped with an exhaust gas recirculation control valve (9); a crank angle sensor (11) that detects an indicated mean effective pressure fluctuation rate (cPi) as an indicator of combustion stability of the internal combustion engine (1); and a controller (10) that corrects the EGR rate of the exhaust gas recirculation unit based on the combustion stability. The controller (10) is configured to: increase-correct the EGR rate by a predetermined amount when the state where the indicated mean effective pressure fluctuation rate (cPi) is lower than a threshold value continues for a predetermined number of cycles; and decrease-correct the EGR rate by a predetermined amount immediately when the indicated mean effective pressure fluctuation rate (cPi) is higher than or equal to the threshold value.

A CPU stops combustion control of Cylinder #1 in order to perform a regeneration process of a GPF and performs a regeneration process of causing an air-fuel ratio of an air-fuel mixture in Cylinders #2 to #4 to be richer. When it is determined that a misfire has occurred because a misfire rate when the regeneration process is not being performed is equal to or greater than a predetermined value, the CPU determines that an internal combustion engine has returned to a normal state based on the premise that the misfire rate when the regeneration process is not being performed decreases.

To provide a controller for internal combustion engine which suppresses that estimation of the combustion state is performed based on the angle information on which the component due to the torsional vibration is superimposed, when the torsional vibration occurs in the crankshaft. A controller for internal combustion engine determines whether a torsional vibration occurs in a crankshaft based on an angle period; calculates a gas pressure torque in burning based on a crank angle acceleration which is calculated based on the angle period; estimates a combustion state of an internal combustion engine based on the gas pressure torque in burning; and stops estimation of the combustion state, when it is determined that the torsional vibration occurred.

Provided is an internal combustion engine control device that is capable of accurately estimating a stable combustion state at low cost. An internal combustion engine control device according to one aspect of the present invention includes: a rotational speed calculation unit 122a that calculates a time-series value of a crank rotational speed of an internal combustion engine; a rotational, speed phase calculation unit 122b that calculates a phase of the crank rotational speed from the time-series value of the crank rotational speed calculated by the rotational speed calculation unit; and a cycle variation calculation unit 122c that calculates the magnitude of variation between cycles of the phase of the crank rotational speed calculated by the rotational speed phase calculation unit.

Provided is an internal combustion engine control device that is capable of accurately estimating a stable combustion state at low cost. An internal combustion engine control device according to one aspect of the present invention includes: a rotational speed calculation unit 122a that calculates a time-series value of a crank rotational speed of an internal combustion engine; a rotational, speed phase calculation unit 122b that calculates a phase of the crank rotational speed from the time-series value of the crank rotational speed calculated by the rotational speed calculation unit; and a cycle variation calculation unit 122c that calculates the magnitude of variation between cycles of the phase of the crank rotational speed calculated by the rotational speed phase calculation unit.